All Alert Logic customers that subscribe to one or more of the Alert Logic products, Threat Manager, Log Manager, or Web Security Manager, with a physical appliance will use this topic for installing the physical appliance.
This topic is not a complete guide to network connectivity. To install the Alert Logic physical appliance, you must have previous experience in network installation. For more information about how to connect the physical appliance to your network, review the Dell hardware documentation for Log Manager, Threat Manager, or Web Security Manager appliances. Refer to the System Requirements page for the minimum system requirements to communicate with the physical appliance.
Claim your Appliance
You must copy the Unique Registration Key to claim your appliance.
To access your Unique Registration Key:
- Click the Settings menu icon () in the upper right-hand corner.
- Click Support Information.
- On the Details page, note your Unique Registration Key.
- Visit the URL that refers to the appliance to be claimed. This URL is https://<Appliance Public IP>. This URL will take you to a web page where you can enter the appliance's Unique Registration Key.
- Submit the Unique Registration Key on the appliance claim page accessed at the appliance URL you generated from its public IP address, and then click Claim Appliance.
To install the physical appliance:
- Use the enclosed installation instructions to properly mount the appliance in the rack.
- Use the ports on the back panel to connect the appliance to your network.
- Connect a network cable from the red Ethernet management port on the appliance to the switch port and VLAN associated with the IP address allocated for the appliance.
Connect the network cable from the appliance monitor ports to the switch ports or network taps. The number and media type of monitor ports vary based on deployment.
With the exception of the red Ethernet management port, any Ethernet port may be used as a monitor port.
- Connect to a power source, and then press the power button.
Ethernet activity lights can flicker, even when the appliance is off.
- The appliance provides power auto-sense support for 100-240 VAC at 50/60 Hz.
- On older models, the power light does not display when you power on the appliance.
- Contact the Alert Logic Security Operations Center (SOC) to request a connectivity test.
- In the US, call (877) 484-8383, and then select option 2.
- In the EU, call +44 (0) 203 011 5533, and then select option 2.
Alert Logic ships appliances with a preconfigured network IP address. If you need to add or update an appliance IP address, you must use the network configuration utility Alert Logic provides for this purpose.
To access the network configuration utility on the appliance, you must connect either of the following devices to the appliance:
- A USB keyboard and monitor connected to a USB connector and the VGA connector on the appliance.
- An IP-based KVM attached to the appliance.
To configure the network:
- Turn on the appliance.
- At the login prompt, use the login name setup and the password provided by Alert Logic.
- In the Configuration Utility, select Network Configuration, and then press Enter.
- Review the instructions, and then press Enter.
- Press Enter to continue.
- On the Interfaces screen, press Enter to continue.
The Interfaces screen displays the connected interfaces. Typically, eth0 is the management interface as designated on the back of the sensor. However, other configurations could require management on a different interface.
- Select the desired management interface, and then press Enter.
- Provide the IP address default gateway and subnet mask. Use the arrow keys to switch between fields.
Optional: Provide two DNS server IPs that the appliance can use instead of the default Google DNS servers.
- Press Enter.
- Press Enter to confirm configuration.
Reconnect any network cables that you previously disconnected.
To apply network changes:
- From the Main Menu, select Restart Networking, and then press Enter to apply the configuration changes performed in the previous section.
- Select Show Current IP/Hostname/Routing Table to verify the changed interface and IP configuration.
The configured Default Gateway appears with a destination of 0.0.0.0 , a flag of UG, and your enterprise default gateway.
You can contact Alert Logic to verify connectivity with the appliance. The appliance should be reachable on your local network.
Confirm communication ability
You can perform this optional procedure to verify the physical appliance can communicate with other IP addresses.
- From the main menu, select Ping an IP, and then press Enter.
- Provide an IP address in the form provided, and then press Enter.
- After you verify communication with the IP address, press Enter.
The Identify Interfaces tool flashes the Link LED of a selected detected interface to assist you with cabling and connections.
To identify interfaces:
- From the Main Menu, select Identify Interface, review the instructions, and then press Enter.
- To continue, press Enter.
- Select the interface to identify, and then press Enter.
To test the network configuration:
- From the Network Configuration Console, select Test Connectivity Using ICMP Ping.
- Enter the IP address of the default gateway.
If you do not see a succession of ping responses, the connectivity test cannot ping the default gateway. Verify that the red Ethernet management port on the appliance is connected to the correct VLAN port, and that your IP information is correct.
After you ping the default gateway successfully, send an email to Alert Logic Onboarding. Provide the IP address of your appliance, or the NAT address if you use a separate internal and external addressing scheme.