Dell R630 physical appliance details

One or two Intel Xeon processor E5-2600 v3 product family

Expansion bus

PCI Express expansion slots using riser card

(Slot 1) One half-height, three fourth-length x8 link (Slot 1) One half-height, half-length x8 link or one half-height, half-length x8 link

(Slot 2) One half-height, half-length x8 link or one half-height, half-length x16 link

1333 MT/s, 1600MT/s, 1866 MT/s, and 2133 MT/s registered Error Correcting Code (ECC) DIMMs

Support for Advanced ECC or memory-optimized operation

Support for LRDIMMs

4 GB, 8 GB, or 32 GB single-, dual-, or quad-ranked

16 GB single- or dual-ranked, or 32 GB dual-ranked.

Up to ten 2.5 inch, internal, hot-swappable SAS, SATA, or Nearline SAS hard drives

One optional SATA DVD-ROM drive or DVD+/-RW drive

NOTE: DVD devices are data only.

Two optional flash memory card slots with the internal SD module

NOTE: One card slot is dedicated for redundancy.

Environmental

NOTE: For additional information about environmental measurements for specific system configurations, see dell.com/environmental_datasheets.

Data center air filtration as defined by ISO Class 8 per ISO 14644-1 with a 95% upper confidence limit.

NOTE: Applies to data center environments only. Air filtration requirements do not apply to IT equipment designed to be used outside a data center, in environments such as an office or factory floor.

NOTE: Air entering the data center must have MERV11 or MERV13 filtration.

• Air must be free of corrosive dust.
• Residual dust present in the air must have a deliquescent point less than 60% relative humidity.

NOTE: Applies to data center and non-data center environments.

1908 BTU/hr maximum (495 W power supply)

2891 BTU/hr maximum (750 W power supply)

2843 BTU/hr maximum (750 W Titanium power supply)

4100 BTU/hr maximum (1100 W power supply)

NOTE: Heat dissipation is calculated using the power supply wattage rating.

100–240 V AC, autoranging, 50/60 Hz

or 200–240 V AC, autoranging, 50/60 Hz, for 750 W Titanium power supply

NOTE: This system is also designed to be connected to IT power systems with a phase-to-phase voltage not exceeding 230 V.

4416 BTU/hour maximum

NOTE: Heat dissipation is calculated using the power supply wattage rating.

–(48–60) V DC

NOTE: This system is also designed to be connected to IT power systems with a phase to phase voltage not exceeding 230 V.

10°C to 35°C (50°F to 95°F) with no direct sunlight on the equipment.

NOTE: Maximum of 145 W 14–core processor is supported in systems with eight 2.5 inches drives 2–PCI slot chassis, and 75 W single wide active GPU.

• Ambient temperature is restricted to 30°C for systems with eight 2.5 inches drives or ten 2.5 inches drives chassis, with no PCIe SSD and a maximum of 160 W workstation processor.
• Ambient temperature is restricted to 30°C for systems with ten 2.5 inches drives chassis, PCIe SSD and a maximum of 135 W processor.
• Ambient temperature is restricted to 35°C for systems with ten 2.5 inches drives chassis, PCIe SSD and a maximum of 120 W processor.
• Ambient temperature is restricted to 35°C for systems with twenty four 1.8 inches drives chassis, PCIe SSD, and a maximum of 135 W processor.

Expanded operating temperature

NOTE: When operating in the expanded temperature range, system performance may be impacted.

NOTE: When operating in the expanded temperature range, ambient temperature warnings may be reported on the LCD and in the System Event Log.

5°C to 40°C at 5% to 85% RH with 29°C dew point.

NOTE: Outside the standard operating temperature (10°C to 35°C), the system can operate continuously down to 5°C or as high as 40°C.

For temperatures between 35°C and 40°C, de-rate maximum allowable temperature by 1°C per 175 m above 950 m (1°F per 319 ft).

–5°C to 45°C at 5% to 90% RH with 29°C (84.2°F) maximum dew point.

NOTE: Outside the standard operating temperature (10°C to 35°C), the system can operate down to –5°C or up to 45°C for a maximum of 1% of its annual operating hours.

For temperatures between 40 °C and 45 °C, de-rate maximum allowable dry bulb temperature by 1°C per 125 m above 950 m (1°F per 228 ft).

• Do not perform a cold startup below 5°C.
• The operating temperature specified is for a maximum altitude of 3048 m (10,000 ft).
• PCIe SSD and 1.8 inch SSDs are not supported.
• GPU is not supported.
• 145 W and Workstation CPU (160 W) processors are not supported.
• Two power supply units are required and one power supply unit failure is not supported.
• Non Dell qualified peripheral cards and/or peripheral cards greater than 25 W are not supported.

Used to troubleshoot software and device driver errors when running certain operating systems. This button can be pressed using the end of a paper clip.

Use this button only if directed to do so by qualified support personnel or by the operating system documentation.

Press to toggle the system ID to ON or OFF. If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC setup) press and hold the button for more than 15 seconds.

Used to troubleshoot software and device driver errors when running certain operating systems. This button can be pressed using the end of a paper clip.

Use this button only if directed to do so by qualified support personnel or by the operating system documentation.

Press to toggle the system ID on and off.

If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC setup) press and hold the button for more than 15 seconds.

Used to troubleshoot software and device driver errors when running certain operating systems. This button can be pressed using the end of a paper clip.

Use this button only if directed to do so by qualified support personnel or by the operating system documentation.

Press to toggle the system ID on and off.

If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC setup) press and hold the button for more than 15 seconds.

Press to toggle the system ID on and off. If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter BIOS progress mode.

To reset iDRAC (if not disabled in F2 iDRAC setup) press and hold for more than 15 seconds.

or

Press to toggle the system ID on and off. If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter BIOS progress mode.

To reset iDRAC (if not disabled in F2 iDRAC setup) press and hold for more than 15 seconds.

or